ADLINK PCI-8124-C Advanced 4-CH Encoder Card
ADLINK PCI-8124-C Advanced 4-CH Encoder Card
PCI-8124-C
Advanced 4-CH Encoder Card with High-speed Triggering Function
Key Features
32-bit PCI bus, Rev. 2.2. 33 MHz
Card index switch selection
Encoder input interface: OUT/DIR, CW/CCW, and 1x, 2x, 4x A/B phase
Trigger output up to 5 MHz; encoder input up to 20 MHz
Programmable trigger pulse width: 0.1 us to 3.2765 ms
Input/Output circuit source can be selectable: TTL/Open
Internal high-speed FIFO for four 32-bit comparators as data
Each channel can store 1024 points (32-bit)
PCI-8124-C is a 4-CH trigger board which is suitable for advanced line scan application which need high line rates. PCI-8124-C has internal FIFO to realize the high speed position compare and trigger pulse output.
For this application, ADLINK proposes you can use PCI-8134 and PCI-8124-C together to gain the advantage of motion control and high speed trigger function.
For position compare, PCI-8124-C provides two method: linear function or variable interval.
PCI-8124-C also provides the variety of mapping function between comparator and trigger output. The comparator condition can be associated with latch signal, TTL input and EA/EB signal.
Ordering Information
PCI-8124-CAdvanced 4-CH encoder card with high-speed triggering function
Accessory
DIN-50S-01Terminal Board with one 50-pin SCSI-II connector and DIN-rail mounting
ACL-10250-150-pin SCSI-II cable (mating with AMP-787082-5), 1 M
Specifications
Counter
■Number of Channels
■Trigger Pulse Frequency
■Encoder Counter
■Comparator
■FIFO Capacity
■Encoder Input Frequency
■Trigger Pulse Width
I/O Signals
■Partial I/O Signals
■Partial I/O Signals
Features
■ 32-bit PCI bus, Rev. 2.2. 33 MHz
■ Card index switch selection
■ Four 32-bit quadrature encoder input and trigger output
channels
■Encoder Signals Input Pins
■Encoder Index Signal Input Pin
■Position latch Input Pin
■Trigger Pulse Output Pin
General Specifications
■Connectors
4-CH
5 MHz (max.)
4. 32-bit
14. 32-bit
1.023 points/channel
20 MHz (max.) @ 4 x AB mode
0.1 us to 3.2765 ms
Optically isolated with 2500 VRMS isolation voltage
TTL type
EA and EB
PCI-8124-C
TRG, 5 V pulse output reference to ground
50-pin SCSI-type connector
■Operating Temperature
■Storage Temperature
■ Encoder input interface: OUT/DIR, CW/CCW, and 1x, 2x,
4x A/B phase
■ Trigger output up to 5 MHz
■ Encoder input up to 20 MHz
■ Programmable trigger pulse width: 0.1 us to 3.2765 ms
■ Input/Output circuit source can be selectable: TTL/Open
collector (with isolation)
■ Switch setting for trigger output default level while power on
■ Trigger output pin logic programmable
■Digital filter for individual encoder input channel
■ Internal high-speed FIFO for four 32-bit comparators as data
reload buffer
■ Each channel can store 1.023 points (32-bit)
■ Each trigger output channel is selected from all comparators,
and manual trigger commands
■ Each encoder counter source is selected from comparators
and manual trigger commands
■ Trigger Pulse Counter
■ 14 comparators can select one of 4 trigger output channels
individually
■ 4 comparators for comparing encoder counter and FIFO data
■ 10 comparators for comparing encoder counter and linear data
■ 4 channel TTL output pins for general purpose output or
trigger output
■ 4 channel TTL input pins for general purpose or timer start signal
■ 4 channel high speed latch input pins for counters
■ EZ and Latch input pins can be used for general purpose input
■ Encoder counter clear via EZ input pin as zero operation by
rising or falling edge
■ Programmable interrupt sources from linear data finished,
triggered, FIFO empty/full/low, latched, and TTL input on
■Humidity
Power Consumption
■Slot Power Supply (input)
■External Power Supply (output)
Software Support
■ OS Information
• Windows® 8/7/XP
• RTX 5.x/6.x/8.1a
■ Software Compatibility
• VB/VC++/BCB/Delphi
• Various sample programs with source codes
■ Software Recommendations
• TriggerMaster
Ordering Information
■ PCI-8124-C
Advanced 4-CH encoder card with high-speed
triggering function
Accessories
For more information on terminal boards & cables, please refer to page 3-30.
Terminal Board
■ DIN-50S-01
Terminal board with one 50-pin SCSI-II connector and
DIN-rail mounting
0˚C to +50˚C (32˚F to 122˚F)-20˚C to +80˚C (-4˚F to 176˚F)
5% to 85%, non-condensing
900 mA (Max.) ±5%, 900 mA (Max.)
+5 VDC ±5%, 500 mA (Max.)