OMRON NB7W-TX01B INTERACTIVE DISPLAY PLC
OMRON NB7W-TX01B INTERACTIVE DISPLAY PLC
USB-Serial Conversion Cable
Applicable OS
Windows XP/Vista/7/8/10 *1
Applicable software CX-Thermo version 4.6 or higher
Applicable models
E5@C-T Series, E5@C Series, and E5CB Series
USB interface standard Conforms to USB Specification 2.0
DTE speed
38.400 bps
Connector
specifications
Power supply
Computer: USB (Type A plug)
Digital Temperature Controller: Special
serial connector
Bus power (Supplied from the USB host controller) *2
Power supply voltage 5 VDC
Current consumption 450 mA max.
Output voltage
Output current
Ambient operating
temperature
Ambient operating
humidity
4.7±0.2 VDC (Supplied from USB-Serial
Conversion Cable to the Digital Temperature
Controller.)
250 mA max. (Supplied from USB-Serial
Conversion Cable to the Digital Temperature
Controller.)
0 to 55°C (with no condensation or icing)
10% to 80%
Storage temperature −20 to 60°C (with no condensation or icing)
Storage humidity
10% to 80%
Altitude
Weight
2.000 m max.
| 1746-NI8I SM331 SLC 500 Analog I/O Module Allen Bradley |
| 16710-30 Bently Nevada 16710 Interconnect Cables |
| IC694ALG233 GE PACSystems RX3i Analog Current Input Module |
| 20BC043A0AYNANC0 Allen-Bradley variable frequency drive |
| 1756-EWEB Allen-Bradley Ethernet I/P Enhanced Web Server module |
| 330130-40-01-05 Bently Nevada 3300 XL Standard Extension Cable |
| 70085-1010-118 AI-Tek Instruments Passive Speed Sensor |
| 770085-1010-330 AI-Tek Instruments Passive Speed Sensor |
| 330104-00-16-10-02-05 Proximity Probes Bently Nevada |
| 330190-085-00-00 3300 XL 8mm Proximity Transducer System Bently Nevada |
| 330130-040-01-02 Bently Nevada 3300 XL Extension Cable |
| 330103-01-07-05-02-00 Bently Nevada 3300 XL 8 mm Probe |
Approx. 120 g
Windows is a registered trademark of Microsoft Corporation in the
United States and or other countries.
*1.CX-Thermo version 4.65 or higher runs on Windows 10.
*2.Use a high-power port for the USB port.
Note: A driver must be installed on the computer. Refer to the Instruction
Manual included with the Cable for the installation procedure.
Communications Specifications
Transmission line
connection method
Communications
RS-485: Multidrop
RS-485 (two-wire, half duplex)
Synchronization method Start-stop synchronization
Protocol
Component
Communi
cations *1
Copying
*2
When Digital Temperature Controllers are connected,
set points and RUN/STOP commands can be sent
from the Digital Temperature Controller that is set as
the master to the Digital Temperature Controllers that
are set as slaves.
Slope and offsets can be set for the set point.
Number of connected Digital Temperature
Controllers: 32 max. (including master)
When Digital Temperature Controllers are connected,
the parameters can be copied from the Digital
Temperature Controller that is set as the master to the
Digital Temperature Controllers that are set as slaves.
MELSEC is a registered trademark of Mitsubishi Electric Corporation.
KEYENCE is a registered trademark of Keyence Corporation.
*1.A Temperature Controller with version 2.1 or higher is required for
the FX Series or the KV Series.
*2.Both the programless communications and the component
communications support the copying.
Current Transformer (Order Separately)
Ratings
E54-CT1
E54-CT3
E54-CT1L
E54-CT3L
Dielectric strength 1.000 VAC for 1 min 1.500 VAC for 1 min
Vibration resistance
Weight
Accessories
50 Hz, 98 m/s2
E54-CT1: Approx. 11.5 g
E54-CT3: Approx. 50 g
E54-CT3 Only
Armatures (2)
Plugs (2)
E54-CT1L: Approx. 14 g
E54-CT3L: Approx. 57 g
NB7W-TX01B