OMRON SGMPH-04AAA61D-OY Servo Motor
USB-Serial Conversion Cable
Applicable OS
Windows XP/Vista/7/8/10 *1
Applicable software CX-Thermo version 4.62 or higher
Applicable models
E5@C-T Series, E5@C Series, and E5CB Series
USB interface standard Conforms to USB Specification 2.0
DTE speed
Connector
specifications
Power supply
38.400 bps
Computer: USB (Type A plug)
Digital Temperature Controller: Special serial
connector
Bus power (Supplied from the USB host controller) *2
Power supply voltage 5 VDC
Current
consumption
Output voltage
Output current
Ambient operating
temperature
Ambient operating
humidity
450 mA max.
4.7±0.2 VDC (Supplied from USB-Serial Conversion
Cable to the Digital Temperature Controller.)
250 mA max. (Supplied from USB-Serial Conversion
Cable to the Digital Temperature Controller.)
0 to 55°C (with no condensation or icing)
10% to 80%
Storage temperature −20 to 60°C (with no condensation or icing)
Storage humidity
10% to 80%
Altitude
Weight
2.000 m max.
Approx. 120 g
Windows is a registered trademark of Microsoft Corporation in the
United States and or other countries.
*1.CX-Thermo version 4.65 or higher runs on Windows 10.
*2.Use a high-power port for the USB port.
Note: A driver must be installed on the computer. Refer to the Instruction
Manual included with the Cable for the installation procedure.
Communications Specifications
Transmission line
connection method
Communications
RS-485: Multidrop
RS-485 (two-wire, half duplex)
Synchronization method Start-stop synchronization
Protocol
Component
Communi
cations
Copying *
When Digital Temperature Controllers are connected,
set points and RUN/STOP commands can be sent
from the Digital Temperature Controller that is set as
the master to the Digital Temperature Controllers that
are set as slaves.
Slope and offsets can be set for the set point.
Number of connected Digital Temperature
Controllers: 32 max. (including master)
When Digital Temperature Controllers are connected,
the parameters can be copied from the Digital
Temperature Controller that is set as the master to the
Digital Temperature Controllers that are set as slaves.
MELSEC is a registered trademark of Mitsubishi Electric Corporation.
KEYENCE is a registered trademark of Keyence Corporation.
*Both the programless communications and the component
communications support the copying.
Current Transformer (Order Separately)
Ratings
E54-CT1
E54-CT3
E54-CT1L
E54-CT3L
Dielectric strength 1.000 VAC for 1 min
Vibration resistance
1.500 VAC for 1 min
50 Hz, 98 m/s2
Weight
Accessories
E54-CT1: Approx. 11.5 g
E54-CT3: Approx. 50 g
E54-CT3 Only
Armatures (2)
Plugs (2)
E54-CT1L: Approx. 14 g
E54-CT3L: Approx. 57 g
None
Heater Burnout Alarms and SSR Failure
Alarms
CT input (for heater
current detection)
Models with detection for single-phase
heaters: One input
Maximum heater current 50 A AC
Input current
indication accuracy
±5% FS ±1 digit max.
Heater burnout alarm
setting range *1
CompoWay/F, or Modbus
Baud rate *
Transmission code
9.600. 19.200. 38.400. or 57.600 bps
ASCII
SSR failure alarm setting
range *2
0.1 to 49.9 A (in units of 0.1 A)
Minimum detection ON time: 100 ms *3
Data bit length *
Stop bit length *
Error detection
Flow control
Interface
Retry function
7 or 8 bits
1 or 2 bits
Vertical parity (none, even, odd)
Block check character (BCC)
with CompoWay/F or
CRC-16 with Modbus
None
RS-485
None
0.1 to 49.9 A (in units of 0.1 A)
Minimum detection OFF time: 100 ms
*4
*1.For heater burnout alarms, the heater current will be measured
when the control output is ON, and the output will turn ON if the
heater current is lower than the set value (i.e., heater burnout
detection current value).
*2.For SSR failure alarms, the heater current will be measured when
the control output is OFF, and the output will turn ON if the heater
current is higher than the set value (i.e., SSR failure detection
current value).
*3.The value is 30 ms for a control period of 0.1 s or 0.2 s.
*4.The value is 35 ms for a control period of 0.1 s or 0.2 s.
Communications buffer
Communications
response wait time
217 bytes
0 to 99 ms
Default: 20 ms
*The baud rate, data bit length, stop bit length, and vertical parity can
be individually set using the Communications Setting Level.
Communications Functions
Programless
communica
tions
10
You can use the memory in the PLC to read and write
E5@C parameters, start and stop operation, etc.
The E5@C automatically performs communications with
PLCs. No communications programming is required.
Number of connected Digital Temperature
Controllers: 32 max. (Up to 16 for the FX Series)
Applicable PLCs
OMRON PLCs
CS Series, CJ Series, CP
Series, NJ Series, or NX1P
Mitsubishi Electric PLCs MELSEC Q Series, L Series,
FX3 Series, or iQ-R Series
KEYENCE PLCs
KEYENCE KV Series