KEBA

KEBA KeDrive D3-DP 310 supply module

Product features

• Serial interface modules

(RS 232-C, RS 422/485-A, Current Loop)

• Full-duplex operation

• SSI interface module

• High interference immunity

• Electronic parameter chip

Short description

The SM 2×0/A series consists of serial and SSI interface modules that can be attached directly to a CPU module or

operated with all KEBA control systems by means of bus couplers.

SM 210/A and SM 230/A are serial interface modules and enable the connection of two RS 232-C or RS 422/485-A

serial interfaces. The two communication channels function independent of one another in full-duplex operation.

SM 220/A is a serial interface card. This module enables the connection of a serial 20 mA Current Loop interface. The

interface functions both for the transmitter as well as for the receiver in active or passive operation. DIP switches are

provided on the front for switching the operating mode. At a maximum transmission rate of 9.6 kbits/s, a line length of

up to 1.000 m is possible.

WINGREEN CANOPEN_ADAPTER V5.0_A01 03ZSTI-00-501-RS
WINGREEN DSPB_V4.0_A02 03ZSTI7-00-402-RS
WINGREEN DUDT_DETECTION_V2.0_A01 03ZSTJ0-00-201-RS
WINGREEN FAN_DETECTION V1.0_A05 03ZSTJ3-00-105
WINGREEN FPB_V3.0_A01 03ZSTJ1-00-301-RS
WINGREEN IPB PCB V2.0_A01 03ZSTL6-00-201-RS
WINGREEN LAIB V3.0_A00 034STN1-00-300-RS
WINGREEN LAIB V3.0_A00 034STN1-01-300-RS
WINGREEN PUIM V2.0 034STM4-00-200-RS
WOHNER 31110
WOODHEAD SST-PFB3-VME-2
WOODHEAD APPLICOM PCI4000
WOODWARD 3522-1009 BUM60-1224-54-B-000-VC-A0-0093-0003-G003
WOODWARD 505XT 8200-1312
WOODWARD 5233-2089

SM 250/A is an SSI interface module that enables the connection of up to 4 position measuring systems and is equipped

with sensor failure detection

Serial interface

SM 210/A SM 220/A SM 230/A SM 250/A

Number 2 1 2

Type of interface RS-232-C, 9-pin

Male connector

Current Loop, 9-pin Male

connector

RS-485-A / RS-422-A,

9-pin Male connector

(switchable via SW)

Data transmission rate 1200 to 115200 bits/s,

can be set via SW

1200 to 9600 bits/s,

can be set via SW

1200 to 115200 bits/s,

can be set via SW

Galvanic isolation No No No

Transmission medium Cable, shielded Cable, shielded Cable, shielded

SSI interface (only SM 250/A)

Number 4

Data transmission rate 125 kbit/s, 250 kbit/s, 500 kbit/s, 1 Mbit/s

Galvanic isolation No

Output voltage for encoder supply +24 V DC

Max. current for encoder supply 250 mA per channel

Sensor failure detection Yes

Dimensions, weight

SM 210/A SM 220/A SM 230/A SM 250/A

Height 120 mm

Width 22.5 mm front plate / 32.5 mm incl. K-bus plug

Depth 100 mm

Weight 132 g 132 g 132 g 140 g

发表回复

您的邮箱地址不会被公开。 必填项已用 * 标注