Hirschmann (Belden) RS30-2402O6T1SDAPHH09.0.13 DIN-rail industrial Ethernet switch
Hirschmann (Belden) RS30-2402O6T1SDAPHH09.0.13 is a 26-port DIN-rail managed industrial Ethernet switch from the OpenRail RS30 family.
Built for high-density plant networks, it combines 24 Fast Ethernet copper ports with 2 Gigabit uplink ports (SFP slot + RJ45 copper). Running Professional Layer 2 management software (Software Version 09.0.13), it provides advanced redundancy, network security, and operational diagnostics.
1. Product Introduction / Overview
Manufacturer: Hirschmann / Belden
Product Family: OpenRail RS30 Managed Switch Series
Full Part Number: RS30-2402O6T1SDAPHH09.0.13
Port Count: 26 Ports total (24 × Fast Ethernet + 2 × Gigabit Uplinks)
Software Level: P (Professional Layer 2 Management)
Software Version: HiOS / Software Release 09.0.13
Primary Function: Industrial edge-to-backhaul distribution, providing high-density connection for field devices (PLCs, HMIs, drives) while uplinking via Gigabit to control room backbones.
2. Technical Parameter List
| Category | Parameter / Feature | Specification |
| Port Configuration | Downlink Ports (1–24) | 24 × 10/100BASE-TX, RJ45 (Auto-crossing, Auto-negotiation) |
| Gigabit Uplink 1 | 1 × 1000BASE-X Open SFP Slot (O6 — requires Gigabit SFP transceiver) |
|
| Gigabit Uplink 2 | 1 × 10/100/1000BASE-TX, RJ45 Copper (T1) |
|
| Power Requirements | Operating Voltage | Dual 12/24/48 V DC (9.6 V DC – 60 V DC), Redundant input |
| Terminal Type | 6-pin plug-in terminal block (Power 1, Power 2, Signal Contact) | |
| Power Consumption | Approx. 12 W – 15 W (Model dependent) | |
| Management & Software | Management Type | Professional Software (P) |
| Interfaces | Web-based (HTTP/HTTPS), CLI (Telnet/SSH), SNMP v1/v2c/v3, Industrial HiVision | |
| Redundancy Protocols | HIPER-Ring, MRP (Media Redundancy Protocol), RSTP (IEEE 802.1D-2004) | |
| Diagnostics | Port Mirroring, RMON (1, 2, 3, 9), System Log, LLDP, Topology Discovery | |
| Mechanical Build | Dimensions (W × H × D) | 120 mm × 135 mm × 111 mm |
| Housing Material | Heavy-duty Metal enclosure (IP20) | |
| Mounting | Standard 35 mm DIN Rail |
3. Environmental Tolerance Conditions
| Environmental Factor | Operating / Tolerance Level | Standard / Test Method |
| Standard Operating Temp | 0 °C to +60 °C (S rating) |
IEC 60068-2-1 / 2-2 |
| Relative Humidity | 10% to 95% (non-condensing) | IEC 60068-2-30 |
| Vibration Resistance | 10 Hz – 150 Hz (1 g / 3.5 mm amplitude) | IEC 60068-2-6 |
| Shock Resistance | 15 g (11 ms duration) | IEC 60068-2-27 |
| EMC Immunity | Radiated, Burst, Surge & ESD protected | EN 61000-4-2 through 4-5 |
| Approvals / Safety | cUL 508, cUL 1604 Class 1 Div 2 (Hazardous Locations), CE, FCC |
4. Model Classification & Naming Breakdown
The code RS30-2402O6T1SDAPHH09.0.13 decodes as follows:
RS30 – 24 02 – O6 T1 – S – D – A – P – HH – HH – 09.0.13
│ │ │ │ │ │ │ │ │ │ │ └── Software Revision (v9.0.13)
│ │ │ │ │ │ │ │ │ └────┴──────── Power Supply: 2x 12/24/48V DC
│ │ │ │ │ │ │ │ └───────────────── Software Level: Professional
│ │ │ │ │ │ │ └───────────────────── Approvals: CE, cUL508. Class 1 Div 2
│ │ │ │ │ │ └───────────────────────── Housing: DIN Rail Mount
│ │ │ │ │ └───────────────────────────── Operating Temp: Standard (0°C to +60°C)
│ │ │ │ └───────────────────────────────── Uplink 2 Port: 1x 10/100/1000 Mbit/s RJ45
│ │ │ └──────────────────────────────────── Uplink 1 Port: 1x 1000 Mbit/s SFP Slot
│ │ └───────────────────────────────────────── Uplink Count: 2x Gigabit Ports
│ └──────────────────────────────────────────── Downlink Count: 24x Fast Ethernet Ports
└─────────────────────────────────────────────────── Family: OpenRail Switch Series (Managed)
5. Operating Instructions
Mechanical Installation
Hook the top lip of the DIN rail clip onto the top edge of the 35 mm DIN rail.
Push the bottom of the switch housing against the rail until the retaining spring locks with an audible click.
[Top Clip] ──► ┌──────────┐
│Hirschmann│
│ RS30 │
[DIN Rail] ──► ╞══════════╡
│ Switch │
[Release Latch]──► └────┬─────┘
▼ (Pull down with tool to unmount)
Initial IP Address Configuration
DIP Switch / Auto-Configuration: Out of the box, the device attempts to obtain an IP via DHCP/BootP.
Auto Configuration Adapter (ACA11 / ACA21): Inserting a pre-configured ACA module into the RJ11 serial interface automatically restores saved configurations.
Serial Terminal Setup: Connect a terminal cable to the V.24 interface (RJ11/RS232 connector) at 9600 baud, 8 data bits, 1 stop bit, no parity to manually set the initial IP address via CLI.
6. Fault Diagnosis & Troubleshooting
| Diagnostic LED / Symptom | Possible Cause | Solution / Corrective Action |
| P1 / P2 LED is OFF | No power supply voltage or inverted wire polarity. | Measure terminal voltage (must be $> 9.6\text{ V DC}$). Check wiring polarity. |
| Fault LED (Red) | Hardware error, link loss on a monitored port, or power supply redundancy fail. | Access the Web Interface/CLI log. Check relay alarm output setup. |
| SFP Uplink LED OFF | SFP module unseated, wavelength mismatch, or dirty fiber face. | Verify SFP module compatibility (must be Hirschmann 1G SFP). Inspect and clean optical connectors. |
| Link Flashing Yellow/Green | Duplex mode mismatch or heavy broadcast storm. | Set port speed and duplex mode manually to match connected network equipment. Enable Broadcast Limiter in software. |
7. Related Models in the Same Series
The Hirschmann OpenRail RS20/RS30 family offers scalable port combinations:
RS20 Series (Fast Ethernet Only):
RS20-0800T1T1SDAP: 8 Fast Ethernet TX Ports
RS20-1600T1T1SDAP: 16 Fast Ethernet TX Ports
RS20-2400T1T1SDAP: 24 Fast Ethernet TX Ports
RS30 Series (With Gigabit Uplinks):
RS30-0802O6O6SDAP: 8 Fast Ethernet TX + 2 Gigabit SFP Ports
RS30-1602O6O6SDAP: 16 Fast Ethernet TX + 2 Gigabit SFP Ports
RS30-2402T1T1SDAP: 24 Fast Ethernet TX + 2 Gigabit RJ45 Copper Ports
Note: The legacy RS20/RS30 series is succeeded by the modern Hirschmann BOBCAT (BXP/BXS) series for high-bandwidth applications.
8. Storage Conditions
To maintain functional integrity prior to installation, observe the following parameters:
Storage Temperature Range: -40 °C to +85 °C
Permissible Relative Humidity: 10% to 95%, strictly non-condensing
Atmospheric Protection: Store in a dry, dust-free environment in original ESD protective packaging. Keep clear of corrosive gas atmospheres (e.g., high sulfur or chlorine concentration).
9. Web Indexing Guidelines
To optimize this technical page for search engine visibility:
HTML Title & Headings:
Title Tag: HIRSCHMANN RS30-2402O6T1SDAPHH09.0.13 Technical Specs & Manual
H1 Tag: Hirschmann RS30-2402O6T1SDAPHH09.0.13 Managed Rail Switch
Structured Product Markup (JSON-LD):
JSON
{
“@context”: “https://schema.org/”,
“@type”: “Product”,
“name”: “Hirschmann RS30-2402O6T1SDAPHH09.0.13”,
“description”: “Industrial OpenRail 26-port Managed Rail Switch with 24x 10/100 TX ports, 1x Gigabit SFP slot, and 1x Gigabit TX port.”,
“brand”: {
“@type”: “Brand”,
“name”: “Hirschmann”
},
“category”: “Industrial Network Switches”
}
Google Search Console Submission:
Include the page URL in your sitemap.xml.
Request crawling via the URL Inspection Tool in Google Search Console.