KEBA

KEBA KeControl C5 CP 507/C, 106051 Custom controls

Product features

• Thermoelement type J, K, L

(TM 220/A, TM 240/A)

• For PT100 sensors

(TM 225/A)

• Internal and external cold junction compensation

• High measurement precision

• Sensor failure detection

• Electronic parameter chip

Short description

The TM 2xx/A series consists of temperature measurement modules that can be directly attached to CPU modules and

operated with all product lines of the KEBA control system by means of bus couplers.

TM 220/A, TM 240/A

Analog input modules TM 220/A and TM 240/A enable the direct connection of thermoelements (2-conductor tech

nique). The calibration and linearization of the temperature values takes place via a microcontroller. A sensor failure,

should it occur, is reported to the higher-level central module and can be evaluated in the application.

Two operating modes are supported:

• Display of the actually measured temperature (standard mode)

• Display of the measured voltage in μV

Cold junction compensation can occur via internal temperature measurement at the terminals of the module or optionally

with the aid of external sensor TE 220/A (external terminal temperature compensation).

TM 225/A

Analog input module TM 225/A enables the direct connection of PT100 resistor sensors. Up to four temperature sensors

can be operated with 2- or 4-conductor technique. With the 4-conductor technique, the interference associated with the

conductor lengths is compensated for and the precision of the measurement thereby increased

SSI Interfaces

SCHUMACHER 1442-0010H
SCHUMACHER ATCS-15
SCHUMACHER ATCS-15 1464-0320
SCHUMACHER MDIA-162
SEAGATE ST3630A
SEC PB4-DY
SEC PB4-DYI
SEC PB5-DY
SEC PB5F-DY
SEC PB5F-DYI
SEC PB5F-DYL
SECO B161S-E176
SEF M21.1
SEIDEL MV65WKS-CE310/22PB
SEM MT30R4-37
SEMIKRON SKD62/16
SENTRON LD63F600
SENTRY VREL-11
SERVO MTS30M4-38

Number 4

Data transmission rate 125 kbit/s, 250 kbit/s, 500 kbit/s, 1 Mbit/s

Galvanic isolation According to suggestion of the SSI standard

Resolution Max. 32 bit (number of bits can be configured)

Supported data code Binary code, Gray code

Output voltage for encoder supply +24 V DC

Max. current for encoder supply 250 mA per channel

Line break monitoring Yes

Short-circuit protection Via self-resetting fuse

Dimensions, weight

Height 120 mm

Width 270 mm

Depth 100 mm

Weight 880 g

Environmental conditions

Operating temperature +5 °C … +55 °C

Storage temperature-40 °C … +70 °C

Relative air humidity 10 % to 95 % (non-condensing)

Vibration resistance Acc. to EN 61131-2:2007

Shock resistance Acc. to EN 61131-2:2007

General

Nominal voltage 24 V DC from front (nominal voltage tolerance: 19.2 V DC to 30 V DC acc. to EN 61131-2)

Max. switch-on current 5 A

Overvoltage category II

Protection class III acc. to EN 61131-2:2007

Max. total power consumption 62.5 W- Own power consumption 9 W- Max. output power K-bus 5 V 8.5 W- Max. output power K-bus 24 V 45 W

Protective measures against Polarity reversal

Supply connection terminals Open terminals, pitch 5.08 mm

Reverse polarity protection Yes

Protection rating IP20

发表回复

您的邮箱地址不会被公开。 必填项已用 * 标注