KEBA

KEBA Zentralbaugruppe CU212

Product features

• Cost- and space-optimized compact module,

especially well suited for plastic machines

• Supports the “fast control” concept

• Functions for changeover point recognition

• Connection via high-performance EtherCAT connection

• Direct expandability by means of KeConnect C2 modules

• Extensive diagnostic options

Short description

The IM 270/W is a cost- and space-saving compact module. It combines the typical I/O design for plastic injection

molding machines in one module and offers functions for changeover point detection. In addition to application in the

plastics sector, it can also be used in other areas.

The IM 270/W supports the “fast control” concept. Innovative EtherCAT communication between the compact module

and the CPU module is used here to minimize dead times and thereby greatly reduce reaction times. This increases the

performance of the machine considerably.

Depending on the type of inputs and outputs, various diagnostic possibilities are available, such as the detection of

sensor failures or short circuits.

The IM 270/W is connected to the CPU module via EtherCAT. To adapt the I/O configuration to the application,

KeConnect C2 modules can be attached at the side directly via the K-bus.

Analog outputs

AM 280/A AM 282/A AM 280/B

Number of outputs 4 4 4

Type Voltage output Voltage output Current output

Digital resolution 12 bit 14 bit 12 bit

Signal range ±10 V ±10 V 0 – 20 mA

Galvanic isolation No No No

Conversion cycle 1 ms 1 ms 1 ms

Value of the lowest bit (LSB) 5.32 mV 1.33 mV 5.39 μA

Monotonicity Yes Yes Yes

Load resistance ≥ 1000 Ω ≥ 1000 Ω ≤ 600 Ω

Largest capacitive load ≤ 10 nF ≤ 10 nF

Differential non-linearity ≤±1 LSB

Settling time when changing over the full

range (with ohmic load) ≤ 50 μs

Typ. temp. coefficient analog output error ±20 ppm of scale end value / °C

Max. temp. coefficient analog output error ±30 ppm of scale end value / °C

Largest error at 25 °C ±0.15 % of scale end value

Dimensions, weight

Height 120 mm

Width 22.5 mm front plate / 32.5 mm incl. plug

Depth 100 mm

Weight 135 g

Environmental conditions

Operating temperature +5 °C … +55 °C

Storage temperature-40 °C … +70 °C

Relative air humidity 10 % to 95 % (non-condensing)

Vibration resistance / shock resistance Acc. to EN 61131-2

General

AM 280/A AM 282/A AM 280/B

Supply voltage 24 V DC from K-bus, 5 V DC from K-bus

Overvoltage category II

Protection class III acc. to EN 61131-2

Addressing on K-bus Via 16-digit address switch, on the side

Type of terminals Open – pitch 5.08 mm

Power consumption K-bus 24 V 3.3 W 3.3 W 3.6 W

Power consumption K-bus 5 V 0.3 W 0.3 W 0.3 W

SAT RM3141-01-02 CM3141-01-02
SAUTER AVM234SF132
SBS 82002070
SBS 82002077
SBS P2-100BT-ER/91515902-ER
SBS PFSK165 3BSE027778R1 VP74201-933CW07
SBS PMC-HS-SERIAL
SBS VIPC616
SBS VME-IP-CARRIER VIPC616 91611524
SCANDE INTELLISCANDE14-1064NM SCANLAB
SCANDE INTELLISCANDE14-405NM SCANLAB
SCANLAB INTELLISCANDE III14-532NM SCANLAB
SCHAFFNER FN3416-110-35
SCHENCK FNT-L001
SCHENCK VEG20400

发表回复

您的邮箱地址不会被公开。 必填项已用 * 标注