FOXBORO P0971WV – Generic module
Exceptional Value
The combination of small size, light weight, direct
mounting, standard materials, and wide
measurement capability with high performance
make this an exceptionally cost effective solution for
process pressure measurement.
Direct Process Mounting
Because of their light weight and external threaded
connection, these transmitters can be installed
directly on process piping without mounting
brackets. However, for unique requirements, an
optional bracket is offered and connection can be
made to the standard 1/4 NPT internal thread.
Wide Rangeability
Three absolute pressure versions are offered to
allow spans from 7 to 21 000 kPa (1 to 3000 psi),
and four gauge pressure versions are offered to
allow spans from 7 to 42 000 kPa (1 to 6000 psi).
Refer to IGP20 Transmitter for gauge pressure
vacuum service.
316L ss, Nickel alloy, and Co-Ni-Cr Process
Wetted Parts
With process connection of 316L ss or Nickel
alloy(1), and sensor diaphragm available in either
316L ss, Nickel alloy, or highly corrosion resistant
Co-Ni-Cr, this transmitter is an excellent choice for
the vast majority of process pressure
measurements.
Span and Range Limits for IAP10 and IGP10 Transmitters
Span Limit
Code
Span Limits
MPa
| MOTOMAN | HW9381022 |
| MOTOROAL | 12967-1/13000C |
| MOTOROAL | 21255-1 |
| MOTOROLA | 01-W3324F |
| MOTOROLA | 01-W3394F-03F PMC663J 700860 |
| MOTOROLA | 01-W3914B |
| MOTOROLA | 0188679 0190530 |
| MOTOROLA | 188987-008R 188987-008R001 |
| MOTOROLA | 30-W2960B01A |
| MOTOROLA | 5264 |
| MOTOROLA | 84-W8865B01B |
| MOTOROLA | 84-W8973B01A |
| MOTOROLA | AET-3047 |
| MOTOROLA | AP-4 01-W3394F-03G |
Figure 5. Direct-Connected Transmitter
(Flameproof Version Shown on Left)
High Gauge Pressure Versions
Three high gauge pressure versions with upper
range limits of 52. 105. and 210 MPa (7500. 15 000.
and 30 000 psi) are available in the IGP10 line. Refer
to PSS 2A-1C13 F for detailed specifications.
Sanitary and Pulp and Paper Versions
These transmitters are also available with integral
process connections for use in sanitary and pulp
and paper installations. See PSS 2A-1C13 K and
PSS 2A-1C13 L, respectively.
Flameproof Design
The IAP10 and IGP10 flameproof versions are
designed to meet Agency flameproof and zone
requirements.
Maximum Overrange and Proof Pressure Ratings for IAP10 and IGP10 Transmitters
Span Limit
Code
Maximum Overrange Pressure Rating (a)
Proof Pressure Rating (a) (b)
a. Values listed are in absolute or gauge pressure units, as applicable. Maximum overrange pressure is the maximum pressure that
may be applied without causing damage to the transmitter.
b. Proof pressure ratings meet ANSI/ISA Standard S82.03-1988. Unit may become nonfunctional after application of proof pressure.
c. Span Limit Code F is applicable to IGP10 Transmitter only. Also not available if pressure seals are selected.
Accuracy (Includes Linearity, Hysteresis, and
Repeatability)
If Span is:
Accuracy in % of Span is:
≥ 6.7% of URL
< 6.7% of URL
±0.1%
± 0.10
+
( ) 0.0067
( ) URL
NOTE
————–
Span
Accuracy is at Reference Operating Conditions;
Zero-based Calibrations; Co-Ni-Cr or 316L ss
sensor with silicone fluid; URL = upper range
limit; and span = calibrated span.
Stability
Long term drift is less than ±0.05% of URL per year
over a 5-year period.
Calibration Frequency
The calibration frequency is five years. The five
years is derived using the values of allowable error
(% span), TPE (% span), performance margin
(% span), and stability (% span/month); where:
Performance Margin
Stability
Calibration Frequency —————————————————— M
Ambient Temperature Effect
Total effect for a 28°C (50°F) change within Normal
Operating Condition limits is:
Span Code
Ambient Temperature Effect
C, D, E, and F (a)
±(0.08% URL + 0.05% Span)
a. Span Code F applicable to IGP10 only.
NOTE
For additional ambient temperature effect when
pressure seals are used, see PSS 2A-1Z11 A.
Vibration Effect
Total effect is ±0.2% of URL per “g” for vibrations in
the frequency range of 5 to 500 Hz; with double
amplitudes of 6.3 mm (0.25 in) in the range of 5 to 15
Hz, or accelerations of 3 “g” in the range of 15 to 500
Hz, whichever is smaller, for transmitters with
aluminum housings; and with double amplitudes of
6.3 mm (0.25 in) in the range of 5 to 9 Hz, or
accelerations of 1 “g” in the range of 9 to 500 Hz,
whichever is smaller, for transmitters with 316 ss
housings