SHINKAWA MODEL VM-5S DUAL TACHOMETER
MODEL VM-5S DUAL TACHOMETER
Monitor range Input signal Recorder output Relay output
1 to 1,000rpm 1 VK,RD,FK Series*1 0 4 to 20mADC 1 CH1 : 4 points (SR1,SR2,SR3,SR4)
SR1,SR2,SR3,SR4 Individual output 6 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 OR output SR2,SR4 OR output 2 to 2,000rpm 2 VE Series*2 1 1 to 5VDC
3 to 5,000rpm 3 MS Series*3
2
Output card
/IS or /RE
option
2 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 Individual output SR2,SR4 Individual output 7 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 OR output SR2,SR4 AND output 4 to 10,000rpm 4 VC Series*2
(Voltage output only) 5 to 15,000rpm 3 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 Individual output SR2,SR4 OR output 8 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 AND output SR2,SR4 Individual output 6 to 20,000rpm
7 to 30,000rpm 4 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 Individual output SR2,SR4 AND output A CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 AND output SR2,SR4 OR output 8 to 50,000rpm
A to 99,999rpm 5 CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 OR output SR2,SR4 Individual output B CH1 : 2 points (SR1,SR2) CH2 : 2 points (SR3,SR4)
SR1,SR3 AND output SR2,SR4 AND output
Speed relay
type
(SR1)
Speed relay
type
(SR2)
Speed relay
type
(SR3)
Speed relay
type
(SR4)
Hysterisis set value
(shaped waveform circuit)
(CH1)
Hysterisis set value
(shaped waveform circuit)
(CH2)
Alarm reset
(SR1)
Alarm reset
(SR2)
Alarm reset
(SR3)
Alarm reset
(SR4)
Alarm reset
(OK)
0 Over
speed 0 Over
speed 0 Over
speed 0 Over
speed
0 1.0V 0 1.0V 0 AUTO-RESET 0 AUTO-RESET 0 AUTO-RESET 0 AUTO-RESET 0 AUTO-RESET
1 0.1V 1 0.1V 1 SELF-HOLD 1 SELF-HOLD 1 SELF-HOLD 1 SELF-HOLD 1 SELF-HOLD
1 Under
speed 1 Under
speed 1 Under
speed 1 Under
speed
2 0.2V 2 0.2V 3 0.5V 3 0.5V
Relay mode
(SR1)
Relay mode
(SR2)
Relay mode
(SR3)
Relay mode
(SR4)
Relay mode
(OK)
First
output*
4
Trigger
mode*5
Monitor/pulse
output Isolate output Recorder option
output
Input power supply
requirements*6 Tropical spec.
0 NORMALLY
DE-ENERGIZED 0 NORMALLY
DE-ENERGIZED 0 NORMALLY
DE-ENERGIZED 0 NORMALLY
DE-ENERGIZED 0 NORMALLY
DE-ENERGIZED
0 OFF 0 AUTO 0 Pulse
output
0 4 to 20mADC 2 0 to -10VDC 0 85 to 264VAC
1 ON 1 MANUAL 1 1 to 5VDC 3 0 to 10VDC 1 24VDC
1 NORMALLY
ENERGIZED 1 NORMALLY
ENERGIZED 1 NORMALLY
ENERGIZED 1 NORMALLY
ENERGIZED 1 NORMALLY
ENERGIZED
1 Monitor
output
2 0 to -10VDC 4 0 to -5VDC 2 110VDC
3 0 to 10VDC 5 0 to 5VDC
4 0 to -5VDC
5 0 to 5VDC
INPUT
SPEED/INDICATED
SPEED CHANGED RATIO
(NON-STANDARD
SPECIFICATION)
If the indicated rotation speed is different from the input rotation
speed, enter into the space below.
Input ratio speed rpm rpm
In case of a magnification more than 1, the resolution
deteriorates in proportion to the magnification factor.
SPEED RELAY SET POINT 4 points (SR1,SR2,SR3,SR4)
SPEED RELAY SET
RANGE
More than 1rpm : Speed relay can be set in 1 rpm increments until
110% of monitor range
Less than 1rpm : Speed relay can be set in 0.1 rpm increment
SPEED RELAY SET ACCURACY ±1 digit or less(on digital indicator)
SPEED RELAY SET
VALUE SR1 :
SR2 :
SR3 :
SR4 :
SR2 ≥ SR1 SR4 ≥ SR3
(SR2 ≤ SR1 SR4 ≤ SR3 in case of both under speed)
Preset to 50% of monitor range unless specified otherwise.
SPEED RELAY OUTPUT 4 points (SR1,SR2,SR3,SR4)
ALARM OUTPUT 1 points (OK) or 2 points (OK1,OK2)
ROTOR SPEED LCD digital meter with 5 digits (7 segments, with back light)
LCD bar graph meter (40 segments, with back light)
SPEED RELAY
INDICATOR
SR1,SR3 : (yellow LED)
SR2,SR4 : (red LED)
ABNOR. ALARM INDICATOR OK : (green LED)
BYPASS INDICATOR BYPASS :(red LED)
TRANSDUCER INPUT VK, RD,FK Series, VE Series, MS Series, VC Series
Number of input points : 2 points
SPEED RELAY
HYSTERESIS
Speed relay hysteresis can be specified from 0 to 100rpm. (1rpm step)
SR1 :
SR2 :
SR3 :
SR4 :
Preset to 10rpm unless specified otherwise.
INPUT IMPEDANCE Approx.5k
INPUT VOLTAGE Min.:2Vpk-pk, Max.:100Vpk-pk
MIN. PULSE WIDTH Approx.50μsec
MIN. INDICATED FREQUENCY Lower of 1Hz or under speed setting.
MAX. INPUT FREQUENCY 10kHz
NO. OF INPUT PULSE 1 to 120 pulse
TRIGGER MODE AUTO, MANUAL (selectable)
In case of auto trigger mode, input pulse duty ratio should be
between 10 and 90% and input pulse frequency should be 1Hz and
over. it depends on the target.
NO. OF INPUT P/R Can be specified from 1 to 120 pulse.
Pulses/rev. :
DIMENSION OF TARGET
(Model VK, RD,FK)
CAUTION) To detect a projection(gear), provide surface A of the projection with a concentric
curve.
Do not make it flat.
A= mm
B= mm
C= mm
D= mm
EXTERNAL CONTACT INPUT
(FROM REAR PANEL)
Contact type : Dry contact
Contact f