Woodward SPM-D2-1040B/NYB 8440-2189
Product number: 8440-2189
Manufacturer product number: 8440-2189
Description: Woodward: CONTROL-SPM-D2-1040B/NYB
SPM-D2-1145B/LSXR 8440-2169
SPM-D2-1115B/LSXR 8440-2165
Documentation: Product Spec: 37623. Manual: 37618
3 Phase Paralleling
SPM-D2-1040B/YB 8440-2176
SPM-D2-1010B/YB 8440-2167
SPM-D2-1040B/NYB 8440-2189
SPM-D2-1010B/NYB 8440-2177
Color: yellow
f+
Color: yellow
V-
Color: yellow
V+
Color: yellow
Gen CB – ON
Color: green
Bus CB – ON
here: non-functional
Color: green
Decrease frequency governor output
The “f-” LED indicates if the unit is outputting a pulse to decrease the fre
quency. The “f-” LED illuminates when the relay “speed lower” is energized.
Increase frequency governor output
The “f+” LED indicates if the unit is outputting a pulse to increase the fre
quency. The “f+” LED illuminates when the relay “speed raise” is energized.
Decrease voltage governor output
The “V-” LED indicates if the unit is outputting a pulse to decrease the volt
age. The “V-” LED illuminates when the relay “voltage lower” is energized.
Increase voltage governor output
The “V+” LED indicates if the unit is outputting a pulse to increase the volt
age. The “V+” LED illuminates when the relay “voltage raise” is energized.
Power circuit breaker ON
The “Gen CB – ON” LED indicates if the response of the power circuit break
er is open or closed. The “Gen CB – ON” LED illuminates if the discrete input
“Reply: CB is open” is not energized and will turn off as soon as the discrete
input is energized.
The LED may also be flashing if one of the following cases occurs:
Discrete input “Reply: CB is open” is not energized and the systems U1 and
U2 are not synchronized
Discrete input “Reply: CB is open” is energized and the systems U1 and U2
are synchronized
(The unit checks the status of the discrete input “Reply: CB is open” for plau
sibility. The unit assumes that the systems U1 and U2 are synchronized if the
switch makes contact and that the systems cannot be synchronized if the
switch breaks contact.)
Mains power circuit breaker ON
NOTE: This LED is non-functional, as this control is only designed to oper
ate one circuit breaker.
Configuration may be performed by manually inputting the desired set points utilizing the pushbuttons and the LC
display. In order to facilitate configuring the parameters, the push buttons have been enabled with an
AUTOROLL function. This permits the user to advance to the next setting, configuration screen, digit, and/or
cursor position more rapidly by pressing and holding the corresponding pushbutton.
Display / Select Display / Select
Automatic mode: Display – By pressing this button, the user may navigate
through the displayed measured parameters and alarm messag
es.
Configuration: Select – Advances the LC display to the next configuration
screen. If any values in a configuration screen have been modi
fied with the “Digit” or “Cursor”, then the “Select” button
must be pressed to save the new setting. By pressing this push
button again, the user causes the system to display the next
configuration screen.
Digit Digit
Automatic mode: Digit – no function
Configuration: Digit – Numerical values over the cursor are increased by
one digit. The increase is restricted by the admissible limits (re
fer to the list of parameters included in the appendix). If the
maximum admissible number is reached, the number automati
cally returns to the lowest admissible number.
Clear / Cursor Clear / Cursor
Automatic mode: Clear – Alarms that have occurred may be acknowledged
by pressing this button as long as the fault that triggered the
alarm is no longer present.
Configuration: Cursor – This button moves the cursor one position from
left to right. When the cursor is under the last digit that may be
changed, it may be moved to the first number of the value by
pressing the “Cursor” button again.